EASYGEN 1000 PDF

LogicsManagerTM. A large number of inputs, internal states, CAN values, or constant values can be combined logically to operate a relay contact or an internal. easYgen Series. easYgen – Installation. GR easYgen- – Configuration. GR easYgen – Operation this manual. German. easYgen Series. easYgen – Installation. GR easYgen – Configuration. GR easYgen – Operation.

Author: Gulmaran Zulugar
Country: Sao Tome and Principe
Language: English (Spanish)
Genre: Marketing
Published (Last): 5 November 2013
Pages: 109
PDF File Size: 7.56 Mb
ePub File Size: 15.10 Mb
ISBN: 705-9-61124-533-3
Downloads: 19100
Price: Free* [*Free Regsitration Required]
Uploader: Gardara

Manual easYgen – Genset Control Measuring: If you have not entered the correct password for the required code level, the parameters for resetting easygeb event history are not available refer to the Event History section on page 16 for more information.

Page 75 – Figure This manual describes the programming of the program.

easYgen-1000 Series

Class 1 – Input resistance per path The is used to define the LogicsManager conditions that will enable the critical mode for conditions and explanation of programming refer to on page Manual easYgen – Genset Control Chapter 2. The ratio will be directly measured though a Lambda probe and controlled to a configured value. Internal Flags Page – LogicsManager: Current measuring – terminal assignment – mains current If this protective function is triggered, the display indicates “Start fail”.

Don’t have an account?

The relay is enabled i. On account of the large variety of parameter settings, it is not possible to cover every possible combination.

  COURS CRYPTOGRAPHIE ASYMTRIQUE PDF

Generator, Voltage Phase Rot Parameters The description of the parameters is confined to the illustration via the PC-program.

Geteventlog Interface tab, configure the COM port according to the port, to which you have connected the DPC, and enter the other settings as represented in figure Figure since these are the default settings of the easYgen Idle Mode When the engine is operated at idle speed, undervoltage, underfrequency, and underspeed monitoring are not performed.

Depending on which mode is selected, certain terminals may have a different function. The percentage threshold value indicates the permissible variation of phase current from the arithmetic mean value of all three-phase currents.

According to IEC three different characteristics are available. The latest version of most publications is available at: Manual easYgen – Genset Control NOTE For the selection of the operating mode via the if two different operating modes have LogicsManager been selected simultaneously the control unit will prioritize the modes as follows: Current measuring – generator Connect in application eassygen Discharge body static before handling the control with power to the control turned off, contact a grounded surface and maintain contact while handling the control.

100

Dynamical Display The easYgen easygn measurement display screen “Generator values – overview” provides five configurable display fields. Password System Password system: For these services, you can contact us by telephone, by e-mail, or through the Woodward website.

Electronic controls contain static-sensitive parts. Each percentage point may be scaled to related values measured from the analog input 0 to Ohm, 0 to 20 mA or 4 to 20 mAso that the actual display reflects the measured values i.

  IN4728 DATASHEET PDF

easygen-1000 Genset Control

Download “easygen Genset Control”. Easy programming More information. Some outputs are assigned a function according to the application mode see following table. Page 32 Dasygen 33 – Engine: Before doing maintenance on the electronic control, discharge the static electricity on your body to ground by touching and holding a grounded metal object pipes, cabinets, equipment, etc. If the real power is above the configured limit an alarm will be issued.

Products – Barcol Air

IK 1 – Manual Eeasygen 20channel icri temperature scanner that monitors the temperature values for exceeding or falling below a threshold value, measured through senders on the IK 1. When shipping the unit sattach a tag with the following information: Evaluation of the discrete inputs as well as control of the relay outputs is done via the control unit.

This relay is always energized if speed is detected. Aircraft customers go to Aircraft Product Publications. If the MPU is disabled, the speed may only be monitored using the generator overfrequency monitoring.